Pengaruh variasi kecepatan putar dan diameter tool terhadap sifat mekanik sambungan fssw aluminium alloy 5052 dan baja ss400

Wahid Ramadhan, Nurul Muhayat, T Triyono

Abstract


Friction stir spot welding (FSSW) is a development from solid state welding to jointa different materials (dissimilar). Dissimilar FSSW is widely used in the automotive industry due to the advantages of joining these two materials with weight savings while exploiting the best strength. This research aims to know the effect of welding parameters of rotation speed and tool diameter on mechanical properties on dissimilar FSSW aluminum alloy 5052 and SS400 steel. Variations in rotational speed used is 800, 1250, 1600, 2000 rpm and tool diameter 10, 12, 14 mm. Plunge depth and dwell time in this research were made uniform. This research used a lap joint configuration with aluminum plate placed on the top and steel plate placed on the bottom. Physical characteristics were analyzed through observation of macro and microstructures, while mechanical characteristics through vickers hardness testing and shear tensile testing. The results indicate that the diameter of 10 mm tool and 1600 rpm rotation speed produce the highest tensile shear load value of 2.4 kN with interface fracture.


Full Text:

PDF

References


T. Chen, Process parameters study on FSW joint of dissimilar metals for aluminum-steel, J. Mater. Sci. 44 (2009) 2573–2580.

C.-S. JEON, S.-T. HONG, Y.-J. KWON, H.-H. CHO, H.N. HAN, Material properties of friction stir spot welded joints of dissimilar aluminum alloys, Trans. Nonferrous Met. Soc. China. 22 (2012) s605–s613.

R.S. Mishra, Z.Y. Ma, Friction stir welding and processing, Mater. Sci. Eng. R Reports. 50 (2005) 1–78.

T. Sakayama, G. Murayma, Y. Naito, K. Saita, Y. Miyazakki, H. Oikawa, T. Nose, Dissimilar metal joining technologies for steel sheet and aluminum alloy sheet in auto body. 393 (2012) 91–98.

M.K. Bilici, Effect of tool geometry on friction stir spot welding of polypropylene sheets, Express Polym. Lett. 6 (2012) 805–813.

Z. Shen, X. Yang, Z. Zhang, L. Cui, Y. Yin, Mechanical properties and failure mechanisms of friction stir spot welds of AA 6061-T4 sheets, Mater. Des. 49 (2013) 181–191.

A. Forcellese, F. Gabrielli, M. Simoncini, Mechanical properties and microstructure of joints in AZ31 thin sheets obtained by friction stir welding using “pin” and “pinless” tool configurations, Mater. Des. 34 (2012) 219–229.

K. Elangovan, V. Balasubramanian, M. Valliappan, Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy, Int. J. Adv. Manuf. Technol. 38 (2008) 285–295.

J.M. Piccini, H.G. Svoboda, Effect of pin length on Friction Stir Spot Welding (FSSW) of dissimilar Aluminum-steel joints, Procedia Mater. Sci. 9 (2015) 504–513.

L. Tricarico, R. Spina, D. Sorgente, M. Brandizzi, Effects of heat treatments on mechanical properties of Fe/Al explosion-welded structural transition joints, Mater. Des. 30 (2009) 2693–2700.

S. Bozzi, A.L. Helbert-Etter, T. Baudin, B. Criqui, J.G. Kerbiguet, Intermetallic compounds in Al 6016/IF-steel friction stir spot welds, Mater. Sci. Eng. A. 527 (2010) 4505–4509.


Refbacks

  • There are currently no refbacks.


Mekanika: Majalah Ilmiah Mekanika

ISSN: 1412-7962 || eISSN: 2579-3144

Address :  Jl. Ir Sutami no 36 A, Building I, Faculty of Engineering, Universitas Sebelas Maret, Surakarta.

Phone    :  +62271632163 

email     : mesin@ft.uns.ac.id

 

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License